Close

Tab Content
  • Satty98's Avatar
    08-18-2019, 04:20 PM
    Their the standard ngk copper core. I did put my v power come comeback in. I ran a platinum a wile back I will never do that again. I'm getting new...
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-17-2019, 11:30 PM
    And by the way I have to take screenshots of my pic cuz my phone is way to advance to lower the pixel to post on here. A galaxy Note 9 takes damn...
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-17-2019, 11:28 PM
    . So these are my plugs for one week. I think she's running lean. But I did browse around. And I tottle past my o2 sensor. Their is a split right...
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-17-2019, 01:46 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Your turbo doesn't come with a adjustable wastegate. 8psi should be a fun ride if you look for a better spring. 6psi will be a good all day daily
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-16-2019, 10:08 PM
    I'll check everything tonight. And the fuel tomorrow I wish I can load a video for you that probably would help
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-16-2019, 09:52 PM
    Ignore that. I tryed to load a video of what it is doing
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-16-2019, 09:51 PM
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-15-2019, 10:44 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    You have more room than I do. I havent took any new pics yet. But that was a test slap in to see how much room I have and what size of fans I can fit...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 10:39 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    That's not bad for low boost. A t28 probably be better for a sohc. Its rear to to see a single cam boosted. I have a dohc and I'm running a .63ar. To...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 09:00 PM
    Basically when I hit 5k. She backfires and I can hit any higher rpms. Like when iyou hit maximum rpms and redline. Honestly I think either I jumped...
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-15-2019, 08:26 PM
    It was the ignition control module. Witch I changed out and I'm throwing no code now but it's doing the same thing. Backfires at 5k.
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-15-2019, 06:46 PM
    Ok guy this if for my daily. I have a 98 sl2 also for my daily driver. It went out on me last weekend. I tooke off from a stop sign and about 200...
    11 replies | 193 view(s)
  • Satty98's Avatar
    08-15-2019, 01:17 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Oh its on a second page lol. My bad
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 01:12 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    My new post didnt post. That's weird. Your welcome. When splat that turbo on. Start will low boost and turn up boost with minor adjustment. And u...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 12:21 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Ow by the way I'm turboing with stock internals but iv done some molding to my head and I am running the twine intake cam setup. Other little mods to...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 12:18 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Also. In my experience. Start will low boost like 5psi. Het her running good. Then ajust for higher like 7 to 8. Personally I can street tune up...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-15-2019, 12:08 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    With boost you may need more single. Be ready to ajust. I got mine stable by tottle of 12 turns. Depending on your build. No one can really say what...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-14-2019, 08:25 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Adjust your vr pot. Try 2 more turns and see if that does any thing. And check ur plugs. I went throw 4 sets of plugs tunning tunning mine to get her...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-14-2019, 08:15 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Your welcome. I research for almost 2 years before I started building. Pluse I meet this guy in Seattle Washington a year back. Guy has done some...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-14-2019, 06:56 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Yes. I'm using 1k as my pull ups. And I turned mine conditioner 12 times. Try 1k resistors as ur pull up. Question are you using stock ignition
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-13-2019, 10:13 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Are you obd1 or obd2. The resistor I think your talking about is for your ignition wire in. How did you build your board. For my wasted spark I did...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-13-2019, 06:43 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Check out hpacademy.com. that guys will teach you how to tune. You can even pay for classes from basic 101 efi tuneing to advance mad sciencest...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-13-2019, 01:59 AM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    Iv been playing with it. I playing with the ignition tune but I'm ready for my stock ignition with fuel management only. S brets is a bad ass. He...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-11-2019, 11:14 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    You will still have to set up your general options and do ur fuel map. The fuel for n/a took me a day to dile it in decently. But not perfect get ur...
    35 replies | 736 view(s)
  • Satty98's Avatar
    08-11-2019, 11:11 PM
    Satty98 replied to a thread Request ms2 v3 in Tuning Library
    This got me started. This is the one everyone is saying is floating around. I am running a dohc. And I am running ms2 v3.0. My map now is all...
    35 replies | 736 view(s)
  • Satty98's Avatar
    07-28-2019, 11:23 PM
    I was thinking on going duel pusher. Would that be ok for our cars. Or should I go with a pusher and a puller. I was going to run one off of the ms...
    11 replies | 599 view(s)
  • Satty98's Avatar
    07-24-2019, 11:47 PM
    Everything isn't all bolted in yet cuz I was doing measurements for my downspout my friend will done with it tomorrow. But you can see the hoses are...
    11 replies | 599 view(s)
  • Satty98's Avatar
    07-24-2019, 11:43 PM
    Thank you Bret. That's something I didnt know. So leave it alone. This weekend I hope to get this turd tuned and started. My board for vr....
    11 replies | 599 view(s)
  • Satty98's Avatar
    07-24-2019, 12:33 PM
    But Aaron ha his ran like what s. Brets is saying. I am running obd2. Not obd1. It is a little bit different to wire then obd1 exspshly with...
    11 replies | 599 view(s)
More Activity
About Satty98

Basic Information

Age
34
About Satty98
Location:
Yakima wa.
Interests:
Automotive
Occupation:
Mechanical technician

Statistics


Total Posts
Total Posts
77
Posts Per Day
0.25
General Information
Last Activity
Today 01:00 AM
Join Date
10-22-2018
Referrals
0
No results to display...
No results to display...

11-12-2018


No results to show...