Close

Search:

Type: Posts; User: S.Bretz

Page 1 of 20 1 2 3 4

Search: Search took 0.98 seconds.

  1. Thread: miss me?

    by S.Bretz
    Replies
    1
    Views
    57

    For a good handy call Andy

    For a good handy call Andy
  2. COP or the standard OBD1 waste spark... there...

    COP or the standard OBD1 waste spark... there should be no difference in the ease of tuning between the two. Once you have the parameters set up for the type of ignition system you choose then the...
  3. Does the engine actually change its tone when...

    Does the engine actually change its tone when this happens or it is just the tacho acting up?

    Is the CTS and connector okay?

    What TPS voltage are you getting at idle?

    Has the throttle body...
  4. I have never installed VW coils on a saturn so I...

    I have never installed VW coils on a saturn so I cannot speak about the board modes. I do think that you will need to run it in semi-sequential mode for it to work since you don't have a physical cam...
  5. Replies
    4,649
    Views
    479,851

    I played doctor diag on mine tonight. Still...

    I played doctor diag on mine tonight. Still haven't confirmed the diagnosis.
  6. Its nice to have you aboard.

    Its nice to have you aboard.
  7. Don't be sorry...that is what the message forums...

    Don't be sorry...that is what the message forums are for.
  8. The stock system is a wasted spark system. Obd1...

    The stock system is a wasted spark system. Obd1 needs a low current driver to contol the icm. Obd2 needs two high current drivers to con the coils individually.
  9. There is a difference the MS2 daughter card and...

    There is a difference the MS2 daughter card and the MS3 daughter card. Both plug into the v3.0 motherboard on the 40 pin socket...but they are not the same. The knock box says it solders to the MS3...
  10. I have never used the knock box. It can't hurt to...

    I have never used the knock box. It can't hurt to have it though. The most current knock bo x that diy autotune has is for ms3 only though.
  11. I would install q16. It is part of the high...

    I would install q16. It is part of the high current ignition driver. If you choose use it for something it will still be there. If you don't want to use to you can simply pull the 5v signal off the...
  12. Thread: Trigger points

    by S.Bretz
    Replies
    6
    Views
    180

    Its a GM 6+1 signal. ODB2 uses a VR signal to...

    Its a GM 6+1 signal.

    ODB2 uses a VR signal to the PCM.
    ODB1 sends the VR signal to the ICM. The ICM conditions the signal and transforms it into a hall signal to the PCM.
  13. I do recall seeing the car when it was gold with...

    I do recall seeing the car when it was gold with flames. I'm not sure if he was ever a member here or not.
  14. Thread: Trigger points

    by S.Bretz
    Replies
    6
    Views
    180

    What specifically about the crank trigger would...

    What specifically about the crank trigger would you like to know?
  15. Thread: Trigger points

    by S.Bretz
    Replies
    6
    Views
    180

    I am not sure what you are asking. Can you...

    I am not sure what you are asking. Can you explain what a trigger point is? Something with the crank trigger maybe?
  16. Replies
    11
    Views
    282

    There are a couple of o-rings on the cover that...

    There are a couple of o-rings on the cover that slip into the hole that the input shaft nut is in. If those collapse they can cause shifting issues.
    When I was working at saturn, we would replace...
  17. Replies
    11
    Views
    282

    A good tell of a loosen input shaft nut is a...

    A good tell of a loosen input shaft nut is a delayed first shift into reverse and then a harsh engagement when it finally does shift into reverse.
    If that is what is happening then pull the side...
  18. Replies
    14
    Views
    402

    The suspension is the same across all years....

    The suspension is the same across all years. Though there are some difference between the single cams and twin cams. The twin cams had rear sway bars and a bigger front sway bar. The single cams has...
  19. Replies
    13
    Views
    379

    I have helped someone install a MS3X on a 3.57...

    I have helped someone install a MS3X on a 3.57 board with some mods (he runs 4 egt's and methanol). It was a large learning curve for him but he can't be happier with it. We also have wheel speed...
  20. Replies
    13
    Views
    379

    After a certain MPH the PCM will kick in a rev...

    After a certain MPH the PCM will kick in a rev limiter around 7200. When I had the auto PCM I could tack 1st gear out to past the 8k marking on the gauge and second gear was up there too but 3rd gear...
  21. Replies
    4
    Views
    194

    ^^^^ like that. If you are using the MS then you...

    ^^^^ like that. If you are using the MS then you can count the teeth, add one since there is one missing tooth to the left of the TDC mark and the multiply by 5. 11th tooth would be 11+1 12. 12*5=60....
  22. There should be a hose that comes off the fire...

    There should be a hose that comes off the fire wall and connects to the purge solenoid. The other end of the purge goes to that clip of vacuum lines that is on the throttle body. If I remember...
  23. Replies
    4
    Views
    194

    The missing teeth should not be at TDC, they...

    The missing teeth should not be at TDC, they should be before TDC. If you can, set the missing teeth about 90 degreed ahead of the TDC mark on the pulley then fine tune the trigger offset.

    To...
  24. Replies
    2
    Views
    148

    95's were the best year. They had the newer shit...

    95's were the best year. They had the newer shit in them but still on OBD1 so they didn't throw codes like the code happy OBD2 stuff.
  25. Replies
    11
    Views
    1,096

    Forced Induction A t25 of t28 would max out around 230-240hp. But...

    A t25 of t28 would max out around 230-240hp. But I would go with at least a t3.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4