Close

Search:

Type: Posts; User: S.Bretz

Page 1 of 20 1 2 3 4

Search: Search took 1.54 seconds.

  1. Replies
    16
    Views
    243

    That piston looks like it got a little hot.

    That piston looks like it got a little hot.
  2. Thread: Oil pump mod?

    by S.Bretz
    Replies
    4
    Views
    95

    Yep. Tap a 1/8in npt thread into the top of the...

    Yep.
    Tap a 1/8in npt thread into the top of the oil bypass plug. Thread in a plug that has a 1/4in hole drilled through it (I use a 13/64 but that is an uncommon size). Make sure you grind off some...
  3. Replies
    7
    Views
    139

    Is the purple wire connected to the correct post...

    Is the purple wire connected to the correct post on the starter solenoid?
  4. Replies
    7
    Views
    139

    Also make sure your main engine grounds are...

    Also make sure your main engine grounds are clean... A loose connection or corroded wire will limit current and can cause it not to be able to draw enough current to spin the starter.
  5. Replies
    7
    Views
    139

    Voltage drop the purple wire from the starter...

    Voltage drop the purple wire from the starter back to the relay. If it only has 10.5v then i suspect that it has some high resistance in it somewhere. A voltage drop test will confirm this. If it...
  6. Replies
    4
    Views
    102

    The 96 sounds like a good candidate for a rebuild...

    The 96 sounds like a good candidate for a rebuild and some boost. Let the pictures flow.
  7. Replies
    16
    Views
    243

    If those are stock sleeves then i would find a...

    If those are stock sleeves then i would find a new block. If GE sleeves then rebore it and get bigger pistons.
  8. Replies
    12
    Views
    218

    I would like one.

    I would like one.
  9. Thread: Turbo Blankets

    by S.Bretz
    Replies
    5
    Views
    196

    Maybe I got mine from Treadstone performance. I...

    Maybe I got mine from Treadstone performance. I really don't remember.
  10. Replies
    6
    Views
    187

    1234 is no good. 4123. from left to right when...

    1234 is no good. 4123. from left to right when you are looking at the coil packs (standing in front of the car looking towards the rear).
  11. Replies
    32
    Views
    1,047

    My car used to love 3rd gear in the mp2.

    My car used to love 3rd gear in the mp2.
  12. Replies
    6
    Views
    187

    Common ignition issues with the first gens would...

    Common ignition issues with the first gens would be:
    1) Oil in the spark plug wells from a leaking valve cover. Replace gasket, plugs and wires.
    2) Worn spark plugs. They should be a .040 gap and...
  13. Thread: Turbo Blankets

    by S.Bretz
    Replies
    5
    Views
    196

    i think i got mine from summit...they all cost...

    i think i got mine from summit...they all cost more than you would think something like that should cost.
  14. Replies
    9
    Views
    222

    Welcome. I'm a bit reluctant to the SRT4...

    Welcome.

    I'm a bit reluctant to the SRT4 swap. WHile there was a lot of progress made with then in the Mopar world, the ECOTEC is a strong engine in itself. You could easily swap in a build LSJ...
  15. Replies
    3
    Views
    179

    No need to for the DIS2 with the MS2, you can...

    No need to for the DIS2 with the MS2, you can control the ICM directly with a 1k ohm resistor on the EST wire between the MS and the ICM.

    I would say that you should still drive it on the street....
  16. Replies
    32
    Views
    1,047

    I;m not sure what you mean by snap...

    I;m not sure what you mean by snap connectors...but if they are what I think then you should not be using them.

    Always use a crimp butt connector with the heat shrinks or solder and and shrink...
  17. Replies
    3
    Views
    177

    When I installed the pioneers 6.5's many years...

    When I installed the pioneers 6.5's many years back I mauled those little pins. The speakers are held in by the pressure from the door card.
  18. Replies
    3
    Views
    177

    I think the stock unit in my 95 was 22w per...

    I think the stock unit in my 95 was 22w per channel, peak. It wasn't much but it didn't need to be since the stock speakers were cheap paper cones.
  19. Replies
    2
    Views
    102

    The sail panel is the inside trim panel by the...

    The sail panel is the inside trim panel by the left and right sides of the back window (or c-pillar moldings).
  20. Replies
    31
    Views
    1,200

    I wish I could. I have an 18 month old anchor...

    I wish I could. I have an 18 month old anchor that will prevent me from leaving though. So I hope you guys have a good time. And have a beer for me.
  21. Replies
    7
    Views
    291

    Welcome aboard. What plans do you have for...

    Welcome aboard.

    What plans do you have for it?

    Pictures are always a plus. Especially if you start a build thread.
    This site does have it's own file storage you can use (you may have to...
  22. Replies
    7
    Views
    1,001

    Welcome aboard. Glad we could help broaden your...

    Welcome aboard. Glad we could help broaden your technical knowledge.
  23. Replies
    3
    Views
    108

    Welcome.

    Welcome.
  24. Replies
    10
    Views
    567

    I have a place by me that i go to. I bring the...

    I have a place by me that i go to. I bring the fittings to them and left them know how much hose i need inbetween and the make them up within a day.
  25. Replies
    32
    Views
    1,047

    The stock ecu grounds the injectors too...its...

    The stock ecu grounds the injectors too...its easuer to just cut the wires going into the pcm and route them to the ms.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4