Close

Search:

Type: Posts; User: S.Bretz

Page 1 of 20 1 2 3 4

Search: Search took 2.07 seconds.

  1. Replies
    1
    Views
    39

    The shielding portion gets grounded to. You can...

    The shielding portion gets grounded to. You can use any of the ground pin outs on the db37..then are all attached to the same ground plane on the PCM.
  2. They did that in California.

    They did that in California.
  3. Replies
    12
    Views
    622

    You can remove the knock sensor from the engine...

    You can remove the knock sensor from the engine and then wrap wire around the threads and then ground it to the engine. This will keep any noise out of the sensor so the PCM will not pull timing.
    A...
  4. Replies
    3
    Views
    264

    A piece of pipe that fits, or a seal installer...

    A piece of pipe that fits, or a seal installer tool. You can usually rent the tool for the parts store for a reasonable amount.
  5. Replies
    9
    Views
    1,189

    The spring doesn't care what car it is on. All...

    The spring doesn't care what car it is on. All that matters is the diameter of the spring perches, the height of the spring and the spring rate.
  6. Replies
    12
    Views
    622

    -50% is wicked low. It shouldn't be pulling...

    -50% is wicked low. It shouldn't be pulling anything under -25% max. If it is pulling that much fuel to make the o2 sensor happy then i would suspect you have a leaking injector, a spark misfire on a...
  7. HOLY CRAP. OBX going for $400. That is insane....

    HOLY CRAP. OBX going for $400. That is insane. You used to be able to get them for $100.
  8. Thread: no cranking

    by S.Bretz
    Replies
    2
    Views
    246

    It could be the safety switch. If that is...

    It could be the safety switch. If that is installed then the next thing I would suspect would be that the BCM lost its learned value for the ignition switch. You can try to perform the 30min learn...
  9. Replies
    1
    Views
    184

    Bump start low to be safe but high enough to make...

    Bump start low to be safe but high enough to make power. If it is N/A then start at maybe 25-26 degrees around peak torque. Make a couple of pulls and to get an idea of what it is making then add a...
  10. Replies
    300
    Views
    44,072

    Yep. I used to joke that Saturn should have...

    Yep. I used to joke that Saturn should have recommended a BCM at the 30k service because the failure rate on them was so high.
  11. Replies
    3
    Views
    274

    You can put the crank pick up right to the MS and...

    You can put the crank pick up right to the MS and then use two coil puts to control the coils on a modded obd2 ICM. There was a guy that did this years back... can't remember his name at the moment...
  12. Replies
    6
    Views
    434

    Naturally Aspirated I used to do something like this back when I had...

    I used to do something like this back when I had the car N/A and on nitrous.

    That stock snorkel going into the box gets round by the box. I cut off the weird shaped part and then ran flexible...
  13. Replies
    46
    Views
    15,601

    Sticky: The wiring diagram you posted looks correct. ...

    The wiring diagram you posted looks correct.
    You will need to trace the leads from spare1 and spare3 back to the processor and make sure the correct options are set on the v3 board.

    IDK why...
  14. It sounds like there is carbon plugging up the...

    It sounds like there is carbon plugging up the egr pentle.
    Take the EGR valve off and give it a quick rev to 4krpm and then shut it off and re-install the EGR. This will help blow excess carbon out...
  15. Replies
    46
    Views
    15,601

    Sticky: Do you have wiring diagrams that I can look at so...

    Do you have wiring diagrams that I can look at so I can see the differences?
  16. Replies
    3
    Views
    377

    I have never heard a flex pipe causing a whistle....

    I have never heard a flex pipe causing a whistle.
    Did you check the header to down pipe flange for any leaks?
    Some of those stock down pipes had a crappy merge at the two-to-one pipe merge. It...
  17. Replies
    5
    Views
    500

    It sounds like the IAC may not being doing what...

    It sounds like the IAC may not being doing what it is supposed to do.

    The EGR may be bad. If it is hanging open, it will cause a low idle. It took my OBD1 95 a year to set a code for a bad EGR...
  18. Replies
    7
    Views
    410

    I do know a guy in your area that spanks the...

    I do know a guy in your area that spanks the Hondas when he get so go racing. I will see if he can post for you.
  19. Replies
    7
    Views
    410

    I cannot answer that second question. I wouldn't...

    I cannot answer that second question. I wouldn't expect much of a change from the flywheel. Though i did run a light flywheel for years i never really noticed a change in power delivery other than...
  20. Replies
    7
    Views
    410

    The cobalt stuff is not a direct fit at all. ...

    The cobalt stuff is not a direct fit at all.

    I'm not sure what you are asking in question 2. The stock flywheel is 18lbs if that is what you are asking.

    You may run into issues with the right...
  21. Replies
    46
    Views
    15,601

    Sticky: The ICM just want a 5v signal to turn on the...

    The ICM just want a 5v signal to turn on the ignition control. It does not care were it comes from.
    Please make sure to use a 1000 ohm resistor on the EST wire that sends the advance signal to the...
  22. Replies
    5
    Views
    500

    They all leak a little bit. The worst one I heard...

    They all leak a little bit. The worst one I heard was on a 400whp DSM; it would whistle at idle.
    This issue shouldn't matter too much on a saturn as the fueling strategy is based off of the MAP...
  23. Thread: Speeduino ECU

    by S.Bretz
    Replies
    4
    Views
    253

    You will not see much power on ethanol on an NA...

    You will not see much power on ethanol on an NA engine...about 3% is typical. I have a feeling your stock clutch may be on its way out.

    The speediuno.... I wondered how long it would take people...
  24. Replies
    22
    Views
    1,214

    Hum... I did a few of them and never had the...

    Hum... I did a few of them and never had the inner part spin. You could try to squeeze the vice a little tighter. I used to have vice jaw marks in the outer sleeve after I was done making one.
  25. Replies
    22
    Views
    1,214

    I really can't remember. It may have been on the...

    I really can't remember. It may have been on the lighter side since i ran tight bearing clearance but i am not sure since i remember at times pouring in bottles of 20-50. I have been known to mix...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4