Close

Search:

Type: Posts; User: alexofnazareth

Page 1 of 20 1 2 3 4

Search: Search took 3.44 seconds.

  1. Ordered 4 belts since stores quit stocking them. ...

    Ordered 4 belts since stores quit stocking them. Thanks!
  2. Replies
    4,288
    Views
    372,538

    Got stuck in a mud pit, got my Tim-bits all wet,...

    Got stuck in a mud pit, got my Tim-bits all wet, soaked [and broked] the alternator, and split one of the trailing arms from the rear subframe during this years Gambler 500. Not my finest moments...
  3. Replies
    4,288
    Views
    372,538

    Sitting outside drinking in relative warmth...

    Sitting outside drinking in relative warmth trying to generate the motivation to follow through with the EDIS install.
    Guess I've become tired of expected failure with this thing.
  4. Replies
    91
    Views
    4,083

    Sticky: Yeah staying local. Time to apply to other...

    Yeah staying local. Time to apply to other positions since there aren't any of interest at Toyota presently.
    Anheuser Busch has a production supervisor position in Tejas :D
  5. Replies
    91
    Views
    4,083

    Sticky: Quit mai jerb. Let the shens begin...

    Quit mai jerb.

    Let the shens begin...
  6. Replies
    9
    Views
    435

    Spray some white lithium into the cylinder to...

    Spray some white lithium into the cylinder to lube up stuck tumblers and shiz?
  7. Replies
    5
    Views
    277

    Also consider buying one of those dingle dangle...

    Also consider buying one of those dingle dangle ball hone deals to clean up the cylinders. I think theyre like 50 bucks.
  8. Replies
    4,288
    Views
    372,538

    grabbed rear calipers at the junkyard to replace...

    grabbed rear calipers at the junkyard to replace the drums with the bleeder screws sheared off on the splaturn.
    Maybe I'll soon have braking that's all uneven/garbage.
  9. Replies
    5
    Views
    319

    In for noodes. Welcome back

    In for noodes.

    Welcome back
  10. Replies
    10
    Views
    392

    fucking kill it.

    fucking kill it.
  11. I spaced down the powertrain 2" since I dropped...

    I spaced down the powertrain 2" since I dropped the subframe 2" as well, which made the original studs far too short to use.
    I used head bolts because they were the only thing long enough in my bolt...
  12. Sam, after drilling a small pilot hole for the...

    Sam, after drilling a small pilot hole for the LHD bit to grab onto, the bolt remnants backed out real easily.
    14628

    Now to find some studs to use for next time:...
  13. Thanks Sam. Holmes Depot only had those screw...

    Thanks Sam. Holmes Depot only had those screw extractor jobbies.
    I've got a lead on a hardware store that sells individual LH bits. Opens at 730 tomorrow morning.
  14. Drilling out "TAM" bolts and ordering new long studs

    Well the offroad turd has finally hit its 2nd hiccup.
    The head bolts that I used in place of the studs for the TAM due to me spacing down the powertrain have failed finally.
    The two outer bolts are...
  15. Replies
    4,288
    Views
    372,538

    Got around to mounting up the SRT4 radiator in...

    Got around to mounting up the SRT4 radiator in "Soap" [Offroad turd].
    I shan't be having problems with bottoming out the front end into a whoop and bending the radiator to fuck again.

    14626
  16. Replies
    1
    Views
    146

    EDIS Trigger wheel - Crank Offset

    Im trying to look around and determine what the offset should be for how I have everything setup for the Trigger wheel and where I placed the sensor.
    So far I can't figure out what the Crank Offset...
  17. Replies
    4,288
    Views
    372,538

    Started wiring up the EDIS to the MS3. Need to...

    Started wiring up the EDIS to the MS3. Need to figure out if MS3 Pin 1 just stays open/unused since only PIP[Pin 24] is used to input tach signal to the MS.
    Used a barbed brass fitting as a...
  18. Plus the same question is asked every other day...

    Plus the same question is asked every other day on Facebook.
  19. Well now that you've gone and said it. Geez. ...

    Well now that you've gone and said it. Geez.

    Lol
  20. Replies
    11
    Views
    494

    Stupid question, do you need another coupler to...

    Stupid question, do you need another coupler to mount the HKS to the turbo or is the HKS inlet rubber similar to a cone filter?
  21. Replies
    8
    Views
    643

    Remove the bumper cover, foam, and aluminum...

    Remove the bumper cover, foam, and aluminum member. It'll reduce the apparent-ness of the poke.
  22. Replies
    11
    Views
    494

    Thanks Sam. Are these able to be cleaned? I'm...

    Thanks Sam. Are these able to be cleaned? I'm imagining that these filters would be similar to those on a dirt bike that can be taken out and cleaned in solvent after they become dirty.
  23. Replies
    11
    Views
    494

    I feel like the abundance of michigan sand would...

    I feel like the abundance of michigan sand would get right past that. I may just put an elbow on it and then place a filter down low to pull in cooler air.
  24. Replies
    11
    Views
    494

    I dont have a lot of space from the inlet of the...

    I dont have a lot of space from the inlet of the turbo to the intercooler piping, so Id like to get a more compact filter than the conventional AEM/K&N cone filter. Also I feel like I've seen...
  25. Replies
    11
    Views
    494

    To not suck shit into the turbo.

    To not suck shit into the turbo.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4