Close

Search:

Type: Posts; User: leighv

Page 1 of 19 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    8
    Views
    471

    lash adjusters cross over . i think someone here...

    lash adjusters cross over . i think someone here made the ecotec sodium filled valves fit?
  2. Replies
    4,674
    Views
    496,159

    crower rods done, crank is getting machined ! :3 ...

    crower rods done, crank is getting machined ! :3
    sending the lower girdle / brace to machine shop tomorrow
  3. Replies
    10
    Views
    768

    can factory ones be rebuilt?

    can factory ones be rebuilt?
  4. i wonder if i could tack weld to build up the...

    i wonder if i could tack weld to build up the shim and file it to fit or something. do you have any extra shims? i need 1.6 mm

    im just deebly goncerned that it will fail somehow.
  5. i measured the clearance without the gasket...

    i measured the clearance without the gasket sealer and its .018 with the retaining ring, the clearance ring is .059" so i need an .080" ring, i guess? I can hand lap it to fit
  6. Manual trans assembly - diff bearing clearance from casing?

    anyone have to set the diff clearance from casing? getting ready to assemble my trans with the Mfactory. everything's ready i just need to order the loctite 515.
  7. Replies
    4,674
    Views
    496,159

    yeth :3 better rod /stroke ratio ! PS crower...

    yeth :3 better rod /stroke ratio !

    PS crower still offers rods
  8. Replies
    4,674
    Views
    496,159

    My new wiseco short CH pistons are completed and...

    My new wiseco short CH pistons are completed and shipping!!
  9. Replies
    9
    Views
    486

    just keep it stock and functioning well. and put...

    just keep it stock and functioning well. and put good tires on it so you can stop on a dime - otherwise enjoy!
  10. Replies
    4,674
    Views
    496,159

    L series rear suspension has stupid sealed...

    L series rear suspension has stupid sealed spherical bearings that are delicate. my mothers car has well over 200K miles and it runs like a champ. we use synthetic oil and ATF. i think it was the...
  11. i think it would look better with tail lights

    i think it would look better with tail lights
  12. Replies
    13
    Views
    847

    Microsquirt is a fairly small module, coupled...

    Microsquirt is a fairly small module, coupled with using a 1G ignition module to clean up signal from the stock sensor may be the best chance.
  13. Replies
    12
    Views
    505

    3g valve cover is fine if you torque to spec and...

    3g valve cover is fine if you torque to spec and use correct torque sequence. make sure gasket surfaces are clean and dry.
  14. Replies
    8
    Views
    858

    Yeah i doubt anyone would take the time to paint...

    Yeah i doubt anyone would take the time to paint springs the same as progress.

    FYI you threw away damn good springs
  15. Replies
    8
    Views
    858

    are those progress sport springs?

    are those progress sport springs?
  16. Replies
    7
    Views
    366

    your best bet is a flat top piston with good...

    your best bet is a flat top piston with good piston/head clearance. instead of the dish piston that only uses a fraction of the quench area
  17. Replies
    7
    Views
    1,023

    be mindful that shortening the transmission side...

    be mindful that shortening the transmission side will increase the force transmitted through the cables -
  18. Thread: AMR Engineering

    by leighv
    Replies
    9
    Views
    697

    hehueuhe

    hehueuhe
  19. Thread: AMR Engineering

    by leighv
    Replies
    9
    Views
    697

    i bought a radiator and it arrived on time but...

    i bought a radiator and it arrived on time but some of the brackets were only tack welded in place...
  20. Replies
    19
    Views
    1,521

    H&R race springs with clapped out KYB's seems to...

    H&R race springs with clapped out KYB's seems to work really good for me . comfortable, not too low, but less roll
  21. Thread: End of an era!

    by leighv
    Replies
    4
    Views
    404

    LSJ swap kit?

    LSJ swap kit?
  22. Replies
    15
    Views
    734

    they're almost extinct now. we just have to deal...

    they're almost extinct now. we just have to deal with it unless someone is interested in making a mount that replicates OEM performance. perhaps one of the hydraulic mounts from later cars can be...
  23. Replies
    15
    Views
    734

    that is the technically correct design, just the...

    that is the technically correct design, just the OEM rubber material used was better at both motion control and absorbing vibration
  24. Replies
    15
    Views
    734

    All mounts are shit except OEM TBH

    All mounts are shit except OEM TBH
  25. Replies
    17
    Views
    1,923

    what ever came of that 3rd gen intake manifold...

    what ever came of that 3rd gen intake manifold someone found in a JY , cast in aluminum?
Results 1 to 25 of 471
Page 1 of 19 1 2 3 4