Close

Search:

Type: Posts; User: S.Bretz

Page 1 of 20 1 2 3 4

Search: Search took 0.81 seconds.

  1. Now that I'm looking at this on computer...

    Now that I'm looking at this on computer monitor...it looks like there is a valley next to the threaded area... that is not normal. You may have an aftermarket pan. Or...maybe someone did a crappy...
  2. Replies
    4,537
    Views
    427,117

    What does it read with the engine off? Should be...

    What does it read with the engine off? Should be about 101kpa at sea level.
  3. You need the gasket on the drain plug. It needs...

    You need the gasket on the drain plug. It needs to be the silicone one.
  4. Replies
    4,537
    Views
    427,117

    It sounds like your map sensor may not be...

    It sounds like your map sensor may not be calibrates correctly.
  5. Replies
    9
    Views
    133

    It starts to get hard to think back that far...

    It starts to get hard to think back that far about those little details.
  6. Good work.

    Good work.
  7. Replies
    24
    Views
    664

    MS does have a steep learning curve.

    MS does have a steep learning curve.
  8. Replies
    24
    Views
    664

    MS does have accurate ignition timing. Last I...

    MS does have accurate ignition timing. Last I checked it was just as accurate that the tech stuff.
  9. At the very least you need to block off that...

    At the very least you need to block off that leaking vac line. A leak on that line will cause a misfire on cylinder #1.
  10. Thread: What?

    by S.Bretz
    Replies
    7
    Views
    260

    What what in the butt?

    What what in the butt?
  11. Replies
    1
    Views
    95

    If it is a new clutch...then just about to the...

    If it is a new clutch...then just about to the top.
  12. This....and years of experience. I only really...

    This....and years of experience. I only really use the service manual for wiring diagrams now a days.
  13. Replies
    3
    Views
    88

    You should be able to loose the striker and...

    You should be able to loose the striker and adjust it in. I think its two T-35 bolts that hold the striker plate in place.
    Measure how far out the door is sticking out.
    Place a piece of painter's...
  14. Replies
    22
    Views
    1,012

    Which one? After owning a Miata for one year Jay...

    Which one? After owning a Miata for one year Jay has thousands of pictures like that.
  15. Replies
    24
    Views
    664

    Just about any of those tune files should work to...

    Just about any of those tune files should work to get you started. You will probably have to change the settings for injectors since your will most likely be different.

    If you use a boosted tune...
  16. Thread: What?

    by S.Bretz
    Replies
    7
    Views
    260

    Freaking ford guys....

    Freaking ford guys....
  17. Replies
    4,537
    Views
    427,117

    I fixed my line locks, adjusted my brake pedal...

    I fixed my line locks, adjusted my brake pedal and did some minor tuning yesterday. Today i drove the turd to work.
  18. Replies
    22
    Views
    1,012

    I wish my car was photogenic.

    I wish my car was photogenic.
  19. Replies
    24
    Views
    664

    They do have a thicker top ring land, but don't...

    They do have a thicker top ring land, but don't think that will help you much. They are still a cast hyperutetic piston and will burn out rather quickly if you run it too lean.
  20. Replies
    2
    Views
    178

    Sand it down. Usually sanding down to the factory...

    Sand it down. Usually sanding down to the factory primer is all you need to do unless the primer is gone.
  21. Replies
    24
    Views
    664

    Yeah...that guy... I wouldn't recommend anything...

    Yeah...that guy... I wouldn't recommend anything he does for tuning as a proper solution.

    As for clutches, usually stage 2's are a stock painted luk pressure plate with a kevlar disc. It has a...
  22. The differences are purely cosmetic.

    The differences are purely cosmetic.
  23. Thread: Noobs uncaged

    by S.Bretz
    Replies
    42
    Views
    8,070

    Sticky: Lock him down!. He's a bot. Saying he's not a...

    Lock him down!. He's a bot. Saying he's not a bot is the first thing a bot would say.
  24. Replies
    24
    Views
    657

    I think you are correct. I was thinking burette...

    I think you are correct. I was thinking burette as I was typing but thought "no...that's the shit girls use in their hair." It has been a long time since I have done a chemistry lab. I know what it...
  25. Replies
    14
    Views
    407

    Tell your dad we said "hi." We miss him...

    Tell your dad we said "hi." We miss him contributing to the shennanagins
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4