Close

Search:

Type: Posts; User: cgg17

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    780

    Take note of the air filter. You will need a new...

    Take note of the air filter. You will need a new cone. Yours looks like it isn't even attached, so you may have been sucking dirt and other stuff into your engine driving around with it like that.
  2. Replies
    9
    Views
    443

    The automatic belts are the best part

    The automatic belts are the best part
  3. Replies
    7
    Views
    479

    I wish you luck, it is a clean looking coupe.

    I wish you luck, it is a clean looking coupe.
  4. Replies
    7
    Views
    479

    Was that the pink/purple one with black leather...

    Was that the pink/purple one with black leather interior?
  5. Replies
    7
    Views
    479

    Where in Eastern PA? I am below Allentown, and...

    Where in Eastern PA? I am below Allentown, and there's a few decent Sl2's around here. Most would need to be manual swapped, but that is easy. There is a 1999 SC2 in the Allentown Harry's U-Pull-It...
  6. Replies
    7
    Views
    979

    I am aware that it will increase the force on the...

    I am aware that it will increase the force on the cables, which may make it feel harder to shift too. I think for a daily, it is good enough for its purpose. Might do the tower mod but maybe in the...
  7. Replies
    7
    Views
    979

    I was shown how to do that, just need to find a...

    I was shown how to do that, just need to find a spare shift tower for myself. Once I find a spare I am most likely going to try it. The only fear I have is it being too hard to shift, as I already...
  8. Replies
    7
    Views
    979

    Short Throw Shifter (no welding required)

    Hello all,
    This is my first post, and I am not 100% sure if it the proper place for it...
    I made myself a short throw shifter, used a hacksaw, drill press, and nice file set. I wanted to do it with...
  9. Replies
    4,661
    Views
    488,989

    It looks half decent, and could actually be...

    It looks half decent, and could actually be converted back to standard if needed. Its under the console now, but has to come out soon as I need to trim some of it to make my new shift boot idea to...
  10. Replies
    4,661
    Views
    488,989

    Wrapped up my homebrew short throw shifter. No...

    Wrapped up my homebrew short throw shifter. No welding, used a hacksaw and a nice set of files. Took me about 8 hours or so of adjusting and fiddling to get it all together. Now that I have one to go...
  11. Replies
    4,661
    Views
    488,989

    All are new, both dogbones, TAM, and trans mount.

    All are new, both dogbones, TAM, and trans mount.
  12. Replies
    4,661
    Views
    488,989

    I found that the plastic dash on the 1995's do...

    I found that the plastic dash on the 1995's do not have the trim piece where it meets the dash, so I put one on and also found that the three metal clips that hold the front end of the dash down were...
  13. Replies
    4,661
    Views
    488,989

    Did some rattle hunting under the dash, got it to...

    Did some rattle hunting under the dash, got it to quiet up a little...
    Also did an Italian tune up on the freeway. Has 160k and still handles high RPM's without sending a rod through the block.
  14. Replies
    4
    Views
    356

    Introduction, New Member From Pennsylvania

    Hello Sixthsphere community,
    I joined the site a while ago, and never really did anything with it besides making my account. I remembered it after talking with a guy from Philly while picking up...
Results 1 to 14 of 15