Close

Search:

Type: Posts; User: S.Bretz

Page 1 of 20 1 2 3 4

Search: Search took 1.29 seconds.

  1. Replies
    2
    Views
    45

    I think the stock unit in my 95 was 22w per...

    I think the stock unit in my 95 was 22w per channel, peak. It wasn't much but it didn't need to be since the stock speakers were cheap paper cones.
  2. Replies
    2
    Views
    31

    The sail panel is the inside trim panel by the...

    The sail panel is the inside trim panel by the left and right sides of the back window (or c-pillar moldings).
  3. Replies
    30
    Views
    810

    I wish I could. I have an 18 month old anchor...

    I wish I could. I have an 18 month old anchor that will prevent me from leaving though. So I hope you guys have a good time. And have a beer for me.
  4. Replies
    3
    Views
    57

    Welcome aboard. What plans do you have for...

    Welcome aboard.

    What plans do you have for it?

    Pictures are always a plus. Especially if you start a build thread.
    This site does have it's own file storage you can use (you may have to...
  5. Replies
    7
    Views
    922

    Welcome aboard. Glad we could help broaden your...

    Welcome aboard. Glad we could help broaden your technical knowledge.
  6. Replies
    3
    Views
    59

    Welcome.

    Welcome.
  7. Replies
    10
    Views
    373

    I have a place by me that i go to. I bring the...

    I have a place by me that i go to. I bring the fittings to them and left them know how much hose i need inbetween and the make them up within a day.
  8. Replies
    18
    Views
    467

    The stock ecu grounds the injectors too...its...

    The stock ecu grounds the injectors too...its easuer to just cut the wires going into the pcm and route them to the ms.
  9. Replies
    18
    Views
    467

    Did you run new injector circuits? Cutting the...

    Did you run new injector circuits? Cutting the oem ones and sending them to the ms works just fine...but i have a feeling that is not an option any more.
  10. Replies
    9
    Views
    167

    Forced Induction A straight to4e may be a bit large. You will not...

    A straight to4e may be a bit large. You will not start seeing any significant boost until about 4k rpm.
    A t3/to4e would be good though.
  11. Replies
    10
    Views
    373

    I have never seen a soft hose go bad but it can...

    I have never seen a soft hose go bad but it can happen if the inner core becomes detatched from the rest of the hose. Maybe get some braided lines made up and see if that fixes it.
  12. Replies
    5
    Views
    230

    Shaking in the steering wheel only when braking...

    Shaking in the steering wheel only when braking is from warped front rotors. You can pick up new white box rotors for about $20 each from a parts store. Or you can have them resurfaced....that will...
  13. Replies
    18
    Views
    467

    You sure it it not a coil? One bad coil will take...

    You sure it it not a coil? One bad coil will take out two cylinders. I had a bad ICM that would not fire one coil.
    If you are using OBD1 you need a resistor between the MS and the OCM on the EST...
  14. The coil pack tower ends need to be clean. If you...

    The coil pack tower ends need to be clean. If you had one corroding and are still using those wires then replace the wires too.
    Double check the order of the plug wires on the coils 4-1-2-3 from...
  15. Replies
    4,487
    Views
    411,917

    The honda transmissions did have an issue with...

    The honda transmissions did have an issue with the converters making a surging feeling at low RPM in high gear...but it was at around 1000-1200 RPM and would go away with higher PRM.

    They do have...
  16. Replies
    4,487
    Views
    411,917

    What trans is in the vue?

    What trans is in the vue?
  17. Replies
    4,487
    Views
    411,917

    I think the knock boards are made by another...

    I think the knock boards are made by another party. Diy probably buys them in bulk and re sells them.
  18. Replies
    30
    Views
    810

    My ribs ... You ladies are missing out.

    My ribs ... You ladies are missing out.
  19. Replies
    4,487
    Views
    411,917

    Was the trans temp super hot ot something?

    Was the trans temp super hot ot something?
  20. Replies
    3
    Views
    244

    Welcome.

    Welcome.
  21. Replies
    4,487
    Views
    411,917

    That must have been neat to meet them.

    That must have been neat to meet them.
  22. Replies
    4,487
    Views
    411,917

    Im interested to know how the knock board works...

    Im interested to know how the knock board works out.
  23. Replies
    13
    Views
    420

    The guy i speak of just beat the shit out of his...

    The guy i speak of just beat the shit out of his comp but lost because he wouldn't do a tear down a 1am and wanted to go home.
  24. Replies
    13
    Views
    420

    Those questions...and...where are you racing? If...

    Those questions...and...where are you racing? If not in the same area as one of my friends i can contact you and maybe set you up with him. He is the best short track turd guy i know and can help you...
  25. Replies
    4,487
    Views
    411,917

    Just cut the entire tube off on the inside.....

    Just cut the entire tube off on the inside.. Leave just enough so that about 1/2 in past the retaining button/rib is there....just enough to hold the snout of the inlet pipe into the air cleaner box....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4