Close

User Tag List

Results 1 to 7 of 7
  1. #1
    6S Resident Hasselhoff. alexofnazareth's Avatar
    Join Date
    Nov 2010
    Location
    Ann Arbor, MI
    Posts
    4,955
    Post Thanks / Like
    Blog Entries
    1
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)

    EDIS Trigger wheel - Crank Offset

    Im trying to look around and determine what the offset should be for how I have everything setup for the Trigger wheel and where I placed the sensor.
    So far I can't figure out what the Crank Offset setting should be in tunerstudio for this:


    ckps.jpg

    Actual TDC lines up with the tooth before the missing tooth [You can see that from the little hatch below the top 8mm bolt]

    If I line the missing tooth up at 12 o'clock, that will put the engine at 10* BTDC with 9 teeth until you reach the CKPS.
    Will I include an offset of 100* in tunerstudio?
    Quote Originally Posted by Donnie View Post
    I see a failboat, steaming full speed on an ocean of failsauce into a barrier reef of lol.
    Quote Originally Posted by BC. Livewire View Post
    if you hate seeing money going down the drane

    than do not turbo your car !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    -----------------------------------------------------------------------------------------------------

    Sixthsphere: Home of newbs, cunts, and Shane Jackson.

  2. #2
    6S Moderator S.Bretz's Avatar
    Join Date
    Apr 2004
    Location
    Lutz, Fl
    Posts
    15,237
    Post Thanks / Like
    Mentioned
    27 Post(s)
    Tagged
    0 Thread(s)
    90 degree back from tdc.
    -6S Resident Mechanical Forensics member #001.
    1995 SC2 Turbo 3.6L DOHC, 6sp manual, Ford 8.8 rearend running on MS3x.
    1998 F-250 5.4L triton...stock.

  3. #3
    6S Resident Hasselhoff. alexofnazareth's Avatar
    Join Date
    Nov 2010
    Location
    Ann Arbor, MI
    Posts
    4,955
    Post Thanks / Like
    Blog Entries
    1
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)
    Everything is up and running with the EDIS. I drove the car to Indy and back without killing it. My current feeling is that it's running pretty good with the current tune I have.

    However I went back to check what offset I put into Tunerstudio and it was still at 10* offset.
    My Advance numbers at cruising are around 40* and if my offset was supposed to be 90* I don't think it would run well at all if it was truly 80* retarded, so like -40*.
    Quote Originally Posted by Donnie View Post
    I see a failboat, steaming full speed on an ocean of failsauce into a barrier reef of lol.
    Quote Originally Posted by BC. Livewire View Post
    if you hate seeing money going down the drane

    than do not turbo your car !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    -----------------------------------------------------------------------------------------------------

    Sixthsphere: Home of newbs, cunts, and Shane Jackson.

  4. #4
    6S Resident Hasselhoff. alexofnazareth's Avatar
    Join Date
    Nov 2010
    Location
    Ann Arbor, MI
    Posts
    4,955
    Post Thanks / Like
    Blog Entries
    1
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)
    I broke out the timing light and used the fixed advance tool in TS. At 0 degrees of advance it's firing very close to TDC (give or take 10* from my view above it)

    So maybe the EDIS option in the ignition section considers where the Ford sensor was originally placed on the wheel.
    Quote Originally Posted by Donnie View Post
    I see a failboat, steaming full speed on an ocean of failsauce into a barrier reef of lol.
    Quote Originally Posted by BC. Livewire View Post
    if you hate seeing money going down the drane

    than do not turbo your car !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    -----------------------------------------------------------------------------------------------------

    Sixthsphere: Home of newbs, cunts, and Shane Jackson.

  5. #5
    6S Resident Hasselhoff. alexofnazareth's Avatar
    Join Date
    Nov 2010
    Location
    Ann Arbor, MI
    Posts
    4,955
    Post Thanks / Like
    Blog Entries
    1
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)
    I broke out the timing light and used the fixed advance tool in TS. At 0 degrees of advance it's firing very close to TDC (give or take 10* from my view above it)

    So maybe the EDIS option in the ignition section considers where the Ford sensor was originally placed on the wheel.
    Quote Originally Posted by Donnie View Post
    I see a failboat, steaming full speed on an ocean of failsauce into a barrier reef of lol.
    Quote Originally Posted by BC. Livewire View Post
    if you hate seeing money going down the drane

    than do not turbo your car !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    -----------------------------------------------------------------------------------------------------

    Sixthsphere: Home of newbs, cunts, and Shane Jackson.

  6. #6
    6S Moderator S.Bretz's Avatar
    Join Date
    Apr 2004
    Location
    Lutz, Fl
    Posts
    15,237
    Post Thanks / Like
    Mentioned
    27 Post(s)
    Tagged
    0 Thread(s)
    I don't remeber how it referneces trigger off set. If you get the tdc mark on the pulley to line up with the timing mark on the front cover then you should be good.
    -6S Resident Mechanical Forensics member #001.
    1995 SC2 Turbo 3.6L DOHC, 6sp manual, Ford 8.8 rearend running on MS3x.
    1998 F-250 5.4L triton...stock.

  7. #7
    6S Resident Hasselhoff. alexofnazareth's Avatar
    Join Date
    Nov 2010
    Location
    Ann Arbor, MI
    Posts
    4,955
    Post Thanks / Like
    Blog Entries
    1
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)
    Yeah, I'll pull the wheel off to get down there tonight.
    Quote Originally Posted by Donnie View Post
    I see a failboat, steaming full speed on an ocean of failsauce into a barrier reef of lol.
    Quote Originally Posted by BC. Livewire View Post
    if you hate seeing money going down the drane

    than do not turbo your car !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    -----------------------------------------------------------------------------------------------------

    Sixthsphere: Home of newbs, cunts, and Shane Jackson.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •